![dsc alarm panel set date and time dsc alarm panel set date and time](https://cms.dsc.com/media/products/lthumbs/i_WT5500.jpg)
- #DSC ALARM PANEL SET DATE AND TIME HOW TO#
- #DSC ALARM PANEL SET DATE AND TIME MANUAL#
- #DSC ALARM PANEL SET DATE AND TIME CODE#
- #DSC ALARM PANEL SET DATE AND TIME SERIES#
Your DSC Security System is made up of a DSC control panel, one or more keypads and various sensors and detectors. To disarm using a key fob simply press and hold the disarm button on a programmed key fob while within range of the system.
#DSC ALARM PANEL SET DATE AND TIME CODE#
To disarm from the panel, simply enter in a valid user code or the Master Code. How Do I Disarm My DSC Alarm System?Disarm from the panel. To program your zone definitions, you must:Enter Programming by pressing ” * 8 + Installer Code “Enter Section 001 (Section 001 is used for Zones 1 – 16 onlyNow you will enter Zone 1’s 2-digit definition.The system will triple beep, and now you will enter zone 2’s definition. This will silence your DSC alarm system keypads. If not, enter your disarm code as usual.2) Enter the *2 which will indicate the trouble condition on most DSC keypads.3) Press the “#” key three times.
#DSC ALARM PANEL SET DATE AND TIME HOW TO#
How to Silence the Beeping Keypad1) Go to any keypad and make sure the system is disarmed. If a sensor fails to reset, it may still be detecting an alarm condition. To reset detectors, press and hold the RESET key () for 2 seconds. Certain sensors (such as smoke detectors and glass break detectors) have to be reset after an alarm. To clear the memory, arm and disarm the system. How do you clear the memory on a DSC alarm?
#DSC ALARM PANEL SET DATE AND TIME SERIES#
How to Acknowledge and Check a Trouble Condition DSC Power Series PC1616, PC1832 and PC1864Press the # key to silence the beeping that accompanies the trouble.Should the Trouble Condition light be active on your system, Press * 2 to enter the Trouble Condition Menu.The Trouble Light will flash. How do I know if my DSC keypad is not working?
#DSC ALARM PANEL SET DATE AND TIME MANUAL#
Change the battery per the panel’s instruction manual if a number 1 appears on the display or the 1 zone is illuminated. Press the star key (*) and then press the number 2 key. How to Troubleshoot Problems on the DSC Home Security SystemPress the pound key (#) to stop the security system from repeatedly beeping. How do you troubleshoot a DSC alarm system? Enter *20.Enter a new 4 digit installer code. Here’s how to do it:Unplug the transformer from the power source.Disconnect the battery.Plug the transformer back in.Reconnect the battery.Within 30 seconds of turning the alarm system on, press * and # at the same time. Thus, you have to ground Z1 to PGM and power the system up for 10 seconds and then power it off, remove the jumper and then power it back on. To do this you have to short the zone 1 pin (not the z1 common pin) with the PGM1 pin. Enter the time in 24 hr format (HH:MM) followed by the date (MM:DD:YY). Time & Date Programming In the event that you need to reset the time and date on your keypad, press, then press to select Time and Date. How do you reset the time on a DSC alarm system? Some alarm systems have two names, the Model Number and the Marketing Name. The metal cabinet contains the system electronics, fuses and back up battery. The control panel, which is a metal cabinet, will be mounted out of the way in a utility closet or in the basement. How to Reset a DSC Alarm After the Power Has Been OffOpen the access door on the unit.Press and hold the “RESET” key for 2 seconds.Press the buttons “*72” if the alarm does not reset after pressing the RESET button.Check the sensors if it still does not turn off.
![dsc alarm panel set date and time dsc alarm panel set date and time](https://zionssecurity.com/wp-content/uploads/2016/09/Screen-Shot-2016-09-19-at-2.21.29-PM.png)
How do I know if my DSC keypad is not working?.How do you troubleshoot a DSC alarm system?.
![dsc alarm panel set date and time dsc alarm panel set date and time](https://safetouch.com/wp-content/uploads/2019/02/ge-image-3.jpg)